Qsys System Design Tutorial

Download PDF
ID 683378
Date 5/04/2015
Public
Document Table of Contents
Document Table of Contents x
1. Qsys System Design Tutorial
1. Qsys System Design Tutorial x
1.1. Software and Hardware Requirements 1.2. Download and Install the Tutorial Design Files 1.3. Open the Tutorial Project 1.4. Creating Qsys Systems 1.5. Assemble a Hierarchical System 1.6. Viewing the Memory Tester System in Qsys 1.7. Compiling and Downloading Software to a Development Board 1.8. Debugging Your Design 1.9. Verifying Hardware in System Console 1.10. Simulating Custom Components 1.11. View a Diagram of the Completed System
1.4. Creating Qsys Systems x
1.4.1. Create a Data Pattern Generator Qsys System 1.4.2. Create a Data Pattern Checker Qsys System
1.4.1. Create a Data Pattern Generator Qsys System x
1.4.1.1. Create a New Qsys System and Set up the Clock Source 1.4.1.2. Add a Pipeline Bridge 1.4.1.3. Add a Custom Pattern Generator 1.4.1.4. Add a PRBS Pattern Generator 1.4.1.5. Add a Two-to-One Streaming Multiplexer 1.4.1.6. Verify the Memory Address Map 1.4.1.7. Connect the Reset Signals 1.4.1.8. Save the System
1.4.2. Create a Data Pattern Checker Qsys System x
1.4.2.1. Create a New Qsys System and Set Up the Clock Soource 1.4.2.2. Add a Pipeline Bridge 1.4.2.3. Add a Custom Pattern Checker 1.4.2.4. Add the PRBS Pattern Checker 1.4.2.5. Add a One-to-Two Streaming Demultiplexer 1.4.2.6. Verify the Memory Address Map 1.4.2.7. Connect the Reset Signals 1.4.2.8. Save the System
1.5. Assemble a Hierarchical System x
1.5.1. Create the Hierarchical Memory Tester System 1.5.2. Complete the Top-Level System
1.5.1. Create the Hierarchical Memory Tester System x
1.5.1.1. Add the Pattern Generator 1.5.1.2. Add the Pattern Checker 1.5.1.3. Add Memory Master Components 1.5.1.4. Connect the Reset Signals 1.5.1.5. Verify the Memory Address Map 1.5.1.6. Save the System
1.5.1.3. Add Memory Master Components x
1.5.1.3.1. Add a Pattern Writer Component 1.5.1.3.2. Add a Pattern Reader Component 1.5.1.3.3. Add a RAM Test Controller
1.9. Verifying Hardware in System Console x
1.9.1. Open the Tutorial Project 1.9.2. Add the JTAG-to-Avalon Master Bridge 1.9.3. Debug with System Console
1.10. Simulating Custom Components x
1.10.1. Generate a Testbench System in Qsys 1.10.2. Run Simulation In the ModelSim-Altera Software
1.10.1. Generate a Testbench System in Qsys x
1.10.1.1. Create a New Qsys System for the Design Under Test 1.10.1.2. Export Design Under Test 1.10.1.3. Generate a Testbench System 1.10.1.4. Generate Testbench System's Simulation Models
1.10.2. Run Simulation In the ModelSim-Altera Software x
1.10.2.1. Set Up the Simulation Environment 1.10.2.2. Run the Simulation
1. Qsys System Design Tutorial

1.4.1. Create a Data Pattern Generator Qsys System

The data pattern generator includes two components to generate test patterns, and a third component to multiplex the data that a processor controls. You configure the pattern generator to match the width of the memory interface. Because the data pattern generator provides a full word of data every clock cycle, configuring the components to match the memory width provides sufficient bandwidth to access the memory.
Note: As you add components and make connections in your Qsys system, error and warning messages appear in the Qsys Messages tab, indicating steps that you must perform before the system is complete. Some error messages appear between steps and are not resolved immediately; as you progress through the tutorial, errors are resolved, and the error messages disappear.

You must use the exact system names described in this tutorial in order for the provided scripts to function correctly.

Level Two Title