DisplayPort Intel® Cyclone 10 GX FPGA IP Design Example User Guide

ID 683603
Date 9/02/2022
Public

A newer version of this document is available. Customers should click here to go to the newest version.

Document Table of Contents

2.6. Clocking Scheme

The clocking scheme illustrates the clock domains in the DisplayPort Intel® FPGA IP design example.
Figure 12.  DisplayPort Intel® FPGA IP Design Example Clocking Scheme
Table 13.  Clocking Scheme Signals
Clock Signal Name in Design Description
TX PLL Refclock tx_pll_refclk

135 MHz TX PLL reference clock, that is divisible by the transceiver for all DisplayPort data rates (1.62 Gbps, 2.7 Gbps, and 5.4 Gbps).

Note: The reference clock source of the TX PLL refclock is located at the HSSI refclk pin.
TX Transceiver Clockout gxb_tx_clkout

TX clock recovered from the transceiver, and the frequency varies depending on the data rate and symbols per clock.

Data Rate Symbols per Clock Frequency (MHz)

RBR (1.62 Gbps)

2 (dual)

81
4 (quad) 40.5

HBR (2.7 Gbps)

2 (dual) 135
4 (quad) 67.5

HBR2 (5.4 Gbps)

2 (dual) 270
4 (quad) 135

HBR3 (8.1 Gbps)

4 (quad) 202.5
 
TX PLL Serial Clock gxb_tx_bonding_clocks

Serial fast clock generated by TX PLL. The clock frequency is set based on the data rate.

RX Refclock rx_cdr_refclk

135 MHz transceiver clock data recovery (CDR) reference clock, that is divisible by all DisplayPort data rates (1.62 Gbps, 2.7 Gbps, 5.4 Gbps, and 8.1 Gbps).

Note: The reference clock source of the RX refclock is located at the HSSI refclk pin.
RX Transceiver Clockout gxb_rx_clkout

RX clock recovered from the transceiver, and the frequency varies depending on the data rate and symbols per clock.

Data Rate Symbols per Clock Frequency (MHz)

RBR (1.62 Gbps)

2 (dual)

81
4 (quad) 40.5

HBR (2.7 Gbps)

2 (dual) 135
4 (quad) 67.5

HBR2 (5.4 Gbps)

2 (dual) 270
4 (quad) 135

HBR3 (8.1 Gbps)

4 (quad) 202.5
 
Management Clock rx_rcfg_mgmt_clk

tx_rcfg_mgmt_clk

A free running 100 MHz clock for both Avalon® memory-mapped interface for reconfiguration and PHY reset controller for transceiver reset sequence.

Component Required Frequency (MHz)
Avalon® memory-mapped reconfiguration 100 – 125
Transceiver PHY reset controller 1 – 500
 
Audio Clock dp_audio_clk

DisplayPort audio clock.

16 MHz Clock clk_16

16 MHz clock used to encode and decode auxiliary channel in the DisplayPort Intel® FPGA IP source and sink IP cores. This clock is also used as a reference clock in the Pixel Clock module for fractional calculation.

Calibration Clock dp_rx_clk_cal

dp_tx_clk_cal

A 50 MHz calibration clock input that must be synchronous to the Transceiver Reconfiguration module's clock. This clock is used in the DisplayPort Intel® FPGA IP core's reconfiguration logic.

RX Video Clock dp_rx_vid_clkout

Video clock for DisplayPort sink to clock video data stream.

If MAX_LINK_RATE = HBR2 and PIXELS_PER_CLOCK = Dual, video clock uses 300 MHz. Otherwise, fixed to 160 MHz.

TX Video Clock tx_vid_clk

Recovered video clock from the PCR module that reflects the actual video clock frequency.

Used when DisplayPort source's TX_SUPPORT_IM_ENABLE = 0.

TX IM Clock tx_im_clk

Video clock for DisplayPort source to clock video data stream. Must be the same as the RX video clock in this design.

Used when DisplayPort source's TX_SUPPORT_IM_ENABLE = 1.